WireGuard 1G IP Core: Hardware-Based Security on AMD FPGA

Secure networking should leave processing power available for your primary application. Design Gateway’s WireGuard1G-IP for AMD FPGAs implements the modern WireGuard VPN protocol directly in programmable logic, delivering a 1 Gbps line-rate hardware engine for robust end-to-end encrypted communication.

A ready-to-run 1G evaluation demo is available on the AMD Kria™ KR260 Robotics Starter Kit, offering engineers and system architects a practical, low-barrier starting point to evaluate an FPGA-based secure tunnel within their own networks.

1 Gbps
Line-Rate Cryptography
0% Host CPU
Dedicated VPN Data Path
AMD KR260
Ready-to-Run Starter Kit

Hardware-Based Security for 1G Networks

Moving computationally intensive VPN processing into dedicated FPGA logic eliminates the requirement to execute the WireGuard protocol engine as host software. Your embedded application processor can dedicate 100% of its CPU cycles to mission-critical system functions while hardware logic autonomously handles secure encrypted connectivity.

Software VPN Bottleneck
  • Host CPU Saturation: Heavy cryptographic routines consume major processor cycles.
  • Latency Jitter: OS scheduling and network context switching introduce nondeterministic delays.
  • Throughput Degradation: Embedded CPUs struggle to sustain gigabit line-rate under concurrent application loads.
Design Gateway Hardware IP
  • Zero CPU Crypto Load: Hardware logic handles handshake, session keys, and packet crypto.
  • Deterministic Low Latency: Pipelined hardware streaming guarantees immediate packet processing.
  • True 1 Gbps Line Rate: Full hardware encryption/decryption without burdening the host operating system.

Clear Architectural Separation: The AMD reference design strictly decouples high-speed packet processing from system management. The FPGA programmable logic handles the continuous data path, while the processing system (PS) simply configures initial tunnel parameters and monitors status. Zero CPU usage for VPN processing specifically refers to the autonomous hardware protocol engine, ensuring total operational efficiency.

Hardware VPN processing and separate configuration control for WireGuard1G-IP on an AMD FPGA.
Figure: WireGuard processing runs in FPGA logic; configuration and monitoring remain separate.

Inside WireGuard1G-IP Architecture

The IP core executes handshakes, key exchanges, authenticated encryption/decryption, and session management entirely within hardware logic. Its state-of-the-art cryptographic engine implements the official WireGuard protocol primitives:

X25519

Key Exchange Engine: Performs hardware-accelerated elliptic curve Diffie-Hellman (ECDH) operations to establish secure ephemeral keys during peer handshakes.

BLAKE2s

Key Derivation & Hashing: Optimized cryptographic hash function providing high-performance MAC, key derivation, and session token generation.

ChaCha20-Poly1305

Authenticated Encryption (AEAD): Stream cipher and authenticator executing continuous, high-throughput payload encryption and data integrity verification.

Streaming Interfaces & Network Protocol Support

  • Integrated Network Controllers: Built-in UDP/IP and ARP controllers manage standard network communications without software driver overhead.
  • 8-bit Streaming Interfaces: Equipped with synchronous 8-bit user and Ethernet MAC streaming interfaces for easy system pipeline integration.
  • IPv4 & Jumbo Frame Support: Full IPv4 packet processing with support for jumbo frames to maximize network data throughput.
  • Layer 3 IP Protection: Secures Layer 3 IP traffic directly. Routing and forwarding decisions belong to surrounding system logic; the AMD reference design provides routing and Ethernet header management alongside the core.
  • MTU Management: IP fragmentation is not handled inside the core, ensuring the tunnel MTU is sized appropriately to account for WireGuard encapsulation overhead.

Evaluate the 1G Demo on AMD KR260

The AMD reference design bridges a local user network to an encrypted tunnel across two Ethernet interfaces. AMD Tri-Mode Ethernet MAC (TEMAC) blocks handle the physical Ethernet links, while integrated routing and header-processing logic steer target packets seamlessly into WireGuard1G-IP.

1

Hardware Setup & Network Topology

Connect your User PC, the AMD Kria KR260 starter kit, and the remote WireGuard endpoint according to the demo guide. Configure local network subnets, endpoint IP addresses, public/private keys, and tunnel endpoints prior to tunnel initialization.

User PC connected through an AMD KR260 WireGuard1G-IP accelerator to a remote WireGuard endpoint.
Figure: 1G evaluation topology using AMD KR260. Use the KR260 demo wiring and address configuration.
2

Configuration and Connection Status

Design Gateway provides an intuitive evaluation GUI utility to import configuration profiles, trigger tunnel activation, and monitor real-time connection status. Following the cryptographic handshake, verify tunnel health and observe packet counters.

WireGuard demo GUI showing the configuration used for the KR260 evaluation.
Figure: Import and review the WireGuard configuration before activation.
WireGuard demo GUI showing an active tunnel and traffic statistics.
Figure: Check handshake completion and connection activity.
3

Application Traffic and Throughput Checks

Validate application-layer connectivity by executing Samba file transfers across the encrypted tunnel. Then, utilize standard iperf3 benchmarking to measure transmit and receive throughput under full-duplex traffic conditions.

Samba file transfer through the WireGuard tunnel in the KR260 evaluation setup.
Figure: Application-level file transfer through the encrypted tunnel.
iperf3 transmit and receive results for the AMD KR260 WireGuard1G-IP demo.
Figure: Full-duplex iperf3 throughput benchmark results through the WireGuard hardware tunnel.

Applications for Secure 1G Connectivity

WireGuard1G-IP is engineered for edge computing, industrial environments, and secure communications where host processor resources cannot be compromised:

Industrial Automation

Protecting critical SCADA field links, robotic controllers, and factory telemetry with deterministic, tamper-proof hardware encryption.

Remote Video & Telemetry

Securing high-resolution camera feeds, UAV downlink feeds, and real-time remote sensors without causing software jitter or frame drop.

Encrypted Edge Backup

Executing continuous, encrypted backups and data logging transfers between remote edge devices and central cloud servers at 1G wire speed.

Core Technical Specifications

Parameter / Feature WireGuard1G-IP Specification
Tunnel Throughput 1 Gbps full-duplex line-rate hardware encryption & decryption
Host CPU Utilization 0% for VPN protocol pipeline (autonomous FPGA hardware engine)
Cryptographic Algorithms X25519 (ECDH key exchange), ChaCha20-Poly1305 (AEAD), BLAKE2s
Protocol Stack Support WireGuard protocol, UDP/IP, ARP, IPv4
User & MAC Interface 8-bit synchronous streaming interface (GMII / TEMAC compatible)
Packet Handling Layer 3 IP packet protection; Jumbo frame support
Target Evaluation Kit AMD Kria™ KR260 Robotics Starter Kit

Supported AMD FPGA Platforms

Design Gateway delivers optimized IP cores and reference designs tailored for AMD programmable logic architectures:

AMD Kria™ KR260 / K26 SOM AMD Zynq™ UltraScale+™ MPSoC AMD Artix™ UltraScale+™ AMD Kintex™ UltraScale+™ AMD 7-Series FPGAs

Official Resources & Evaluation

Explore official Design Gateway resources, reference documentation, and product datasheets for WireGuard on AMD FPGAs:

Need More Bandwidth? WireGuard10G-IP Is Also Available

For high-throughput network aggregation and enterprise-grade data centers, Design Gateway offers WireGuard10G-IP for AMD FPGAs. A complete 10G evaluation demo is available on the AMD Zynq UltraScale+ ZCU106 Evaluation Kit.

Watch the WireGuard 10G Demonstration on ZCU106 on YouTube →

WireGuard 10G Demonstration on AMD ZCU106
AMD ZCU106 Evaluation Demo YouTube
WireGuard 10G Demonstration on AMD ZCU106
Click to watch live full demonstration on YouTube →

Accelerate Your Secure 1G Network on AMD FPGAs

Evaluate WireGuard1G-IP directly on the AMD Kria KR260 Robotics Starter Kit. Get in touch with our engineering team for custom FPGA integration and bitfile evaluation packages.